A parametric study of laser induced thin film spallation

We report parametric studies of elastic wave generation by a pulsed laser and associated spalling of thin surface films by the corresponding high stresses. Two different substrate materials, single crystal Si (100) and fused silica, are considered. Spallation behavior of Al thin films is investigated as a function of substrate thickness, film thickness, laser energy, and various parameters governing the source. Surface displacement due to the stress wave is measured by Michaelson interferometry and used to infer the stresses on the film interface. Consistent with previous studies, the maximum stress in the substrate and at the film/substrate interface increases with increasing laser fluence. For many of the conditions tested, the substrate stress is large enough to damage the Si. Moreover, the maximum interface stress is found to increase with increasing film thickness, but decrease with increasing substrate thickness due to geometric attenuation. Of particular significance is the development of a decompression shock in the fused sillica substrates, which results in very high tensile stresses at the interface. This shock enhances the failure of thin film interfaces, especially in thicker samples.     

The effective properties of composites with fiber-end cracks

The paper describes use of self-consistent finite element method (SCFEM) for predicting effective properties of fiber composite with partially debonded interface. The effective longitudinal Young's modulus and shear modulus for unidirectional fiber reinforced composites with fiber-end cracks are calculated. Numerical results show that the effective properties are considerably influenced by the fiber-end cracks. The effects of microstructural parameters, such as fiber volume fraction, modulus ratio of the constituents and fiber aspect, on the effective properties of the composites were discussed. The project supported by the National Natural Science Foundation of China     

Interaction between an edge dislocation and a circular inclusion with an inhomogeneously imperfect interface

This research presents an analytical study of the interaction problem of an edge dislocation with a circular inclusion with a circumferentially inhomogeneously imperfect interface. The interface, which is modeled as a spring (interphase) layer with vanishing thickness, is characterized by that in which there is a displacement jump across the interface in the same direction as the corresponding tractions, and the same degree of imperfection is realized in both the normal and tangential directions. Furthermore, the interface parameter is nonuniform along the interface. In order to arrive at an elementary form solution, we introduce a conformal mapping function. Then the stress field as well as the Peach–Koehler force acting on the edge dislocation can be obtained from the derived complex potentials. Calculations demonstrate that the nonuniform interface parameter has a significant influence on the stress field.     

Dynamic behaviour of a bubble near an elastic infinite interface

This paper presents a study to describe the behaviour of a non-equilibrium bubble in a fluid (Fluid 1) that is in contact with another fluid (Fluid 2). Fluid 2 is assumed to incorporate some elastic properties, which are modelled through a pressure term at the fluid–fluid interface. The Laplace equation is assumed to be valid in both fluids and the boundary integral method is employed to simulate the dynamics of the bubble and the fluid–fluid interface. Interesting characteristic phenomena concerning bubble oscillations and the deformation of the fluid–fluid interface are studied for a range of parameters (distance from the fluid–fluid interface, density ratios of the two fluids and elastic properties of Fluid 2). Some of the phenomena observed are jet formation in the bubble, bubble splitting, a ring bubble separating from the main bubble, mushroom-shaped bubbles and the dynamic elevation of the elastic interface. Most of these phenomena are only observed when Fluid 2 possesses some elastic properties (besides the usual formation of a high speed liquid jet). Comparisons with experimental observations confirm the validity of our simulations.     

Benchmark solution of angle-ply piezoelectric-laminated cylindrical panels in cylindrical bending with weak interfaces

The bending problem of a simply supported, angle-ply piezoelectric-laminated cylindrical panel in cylindrical bending with weak interfaces is considered. A general spring-layer model is adopted to describe the weakness of imperfect interfaces. An exact analysis is performed via the state-space approach. A new system of physical variables is introduced and a variable substitution technique is employed to derive a state equation with constant coefficients. Numerical results are given to show the effect of weak interfaces.The work was supported by the National Natural Science Foundation of China (No. 10372088) and by the Korea Institute of Science and Technology Evaluation and Planning.     

有限元计算中疏密网格过渡方法研究

工程计算中出于节省计算量的目的,往往需要在一个有限元模型中布置粗细不同的网格。为保证计算结果的准确性,必须保证网格突变情况下的位移协调问题。本文工作之一是在强天驰界面过渡单元的基础上,引入虚拟节点和子单元,在子单元中应用节理元思想,提出了基于最小势能原理的弹簧节理单元法。简化了积分运算,避免了精度要求极高的坐标转换,从而提高了方法的精度和实用性;二是提出了基于位移约束的主从自由度法,简便实用,只需简单的矩阵运算即可实现。两种方法均实现了不同尺寸网格间位移的协调性和刚度的匹配,从而使之满足有限元收敛准则,且生成的刚度阵具有对称性及带状性。算例证明两种方法精度良好,并可方便地应用于求解大规模工程问题。     

Dilational rheology of an air–water interface functionalized by biomolecules: the role of surface diffusion

As an attempt to develop a sensitive device for biomolecule detection, a micromechanical methodology based on the rheological change of an air–water interface is put forward (Berthier and Davoust, CEA/CNRS patent, PCT International Application WO 2003/080209 A3, 2003). Capillary waves induced from the vertical electrodynamic vibration of a brimful cylindrical tank filled with water stand as a good way to identify dilational elasticity and viscosity of an aging interface. Before, we were interested of the fact that complex wave number and the frequency of waves are obtained through an optical technique, which allows us to accurately recognize the whole interface geometry. These two parameters, a modeling based on a dispersion relation (Lucassen-Reynders and Lucassen, Adv Colloid Interface Sci, 2:347, 1969) and the surface mass transport equation, are jointly used to identify the surface diffusivity and the dilational rheology of the interface for a nonsoluble biochemical surfactant. Preliminary results obtained from a water surface functionalized by DNA, thanks to a lipidic monolayer, demonstrate the capabilities of the proposed methodology. The sensitivity of dilational rheology and the surface diffusivity on DNA adsorption on lipids is made evident.This paper was presented at the Annual Meeting of the European Society of Rheology, Grenoble, April 2005.     

Adsorption Mechanism of Comb Polymer Dispersants at the Cement/Water Interface

Comb polymers are commonly used as dispersants to stabilize highly concentrated cement suspensions. The effectiveness of such polymeric additives to stabilize these suspensions is determined to a large extent by the amount adsorbed. In this study we investigated the adsorption characteristics of various comb dispersant containing different graft densities on surfaces of cement particle. The effect of inorganic salts on their adsorption was also examined in order to elucidate their adsorption mechanism. The results show that the adsorption of comb polymer dispersants on cement surface conforms approximately to Langmuir's adsorption isotherm and the characteristic plateau A _s and adsorption free energy ΔG_ads are largely dependent on the anionic group content of the comb polymers. The A _s and ΔG_ads increase with increasing anionic group content. This information suggests that the adsorption of comb polymers on cement surfaces is dominated by electrostatic interaction between COO-groups on the comb polymers and the positive surface of the cement. This conclusion is supported by effects of inorganics such as calcium and sulfate ions, and diffuse reflectance FTIR spectroscopy. The implication of results for tuning polymers for the required performance in cement manufacture should be noted.     

LaAlO_3/SrTiO_3界面增强光伏效应

探索LaAlO_3/SrTiO_3(LAO/STO)界面产生的新奇物理特性对理解关联电子系统中多自由度耦合和设计功能材料器件具有重要的价值.本文通过脉冲激光沉积方法在SrTiO_3基底上制备了LAO/STO薄膜,研究了正面照射LAO/STO膜面和侧面照射LAO/STO界面时的光伏效应,探讨了LAO/STO界面对光伏效应的影响.研究结果表明,在同样光照能量下侧面照射LAO/STO界面产生的光电压远高于正面照射LAO/STO膜面产生的光电压,说明LAO/STO界面对光伏效应有明显的增强作用.通过偏压调控可以进一步增强照射LAO/STO界面产生的光电压,当偏压为60 V时, LAO/STO样品的位置探测灵敏度达到了36.8 mV/mm.这些研究结果为设计场调控位置敏感探测器等新型光电子器件提供了新的思路.     

In-plane oriented CH_3NH_3PbI_3 nanowire suppression of the interface electron transfer to PCBM

One-dimensional nanowire is an important candidate for lead-halide perovskite-based photonic detectors and solar cells. Its surface population, diameter, and growth direction, etc., are critical for device performance. In this research,we carried out a detailed study on electron transfer process at the interface of nanowire CH_3 NH_3 PbI_3(N-MAPbI_3)/Phenyl C61 butyric acid methyl-ester synonym(PCBM), as well as the interface of compact CH_3 NH_3 PbI_3(C-MAPbI_3)/PCBM by transient absorption spectroscopy. By comparing the carrier recombination dynamics of N-MAPbI_3, N-MAPbI_3/PCBM,C-MAPbI_3, and C-MAPbI_3/PCBM from picosecond(ps) to hundred nanosecond(ns) time scale, it is demonstrated that electron transfer at N-MAPbI_3/PCBM interface is less efficient than that at C-MAPbI_3/PCBM interface. In addition, electron transfer efficiency at C-MAPbI_3/PCBM interface was found to be excitation density-dependent, and it reduces with photo-generation carrier concentration increasing in a range from 1.0 × 1018 cm~(-3)–4.0 × 1018 cm~(-3). Hot electron transfer,which leads to acceleration of electron transfer between the interfaces, was also visualized as carrier concentration increases from 1.0 × 10~(18) cm~(-3)–2.2 × 10~(18) cm~(-3).